Clik here to view.
Error in New Version SS6
Hi All,I just installed STAAD pro SS6 latest version and open previous version file(SS5) in new version, but it shows following warning that I had not faced in previous versionplease suggest see below...
View ArticleRE: *** WARNING:CMN PARAM INVALID FOR NATIONAL ANNEX
Ok But what should be the conclusion? Does it means i have to specify CMN 1 for all in spite of fixed (welded) at ends?
View Article*** WARNING:CMN PARAM INVALID FOR NATIONAL ANNEX
I am designing a welded steel structure.As structure is welded i have mentionedCMN 0.5 to beamsCMN 0.7 to columns (fixed support at bottom of column and tied using beams at top )It is showing...
View ArticleClik here to view.
RE: Unique Condition at EOS Modeling Advice
Your approach seems sound, but conservative. If you look at the moment contours (or deflection contours) I think you will see a fairly traditional behavior a few feet from the wall supported edge. By...
View ArticleRE: Shear wall design
It is difficult to tell what is the exact cause without looking at the models but here are some pointers. The slab would help in reducing the out of plane bending of the beams/columns and shear walls...
View ArticleRE: Shear wall design
Hi Sye,here are the two models if you wish to take a better look.(Please visit the site to view this file)
View ArticleClik here to view.
Shear wall design
Good Day fellow colleagues,I have tested two models to complete a shear wall design using staad pro. In one model I included only the shear walls, beams and columns and in the other model I included...
View ArticleRE: Ram concept modal mass in Vibration analysis
Unfortunately, while we are calculating the modal mass (mass participation) of each vibration mode they are not stored or exposed to the user currently. I added an enhancement request (#494917) to...
View ArticleRam concept modal mass in Vibration analysis
hi,i would like to work out the modal mass from the Vibration analysis in Ram Concept.how is it possible to see this result in Ram Concept?I saw the Frequencies for each mode shapes but i am not be...
View ArticleClik here to view.
RE: Can anyone provide design file of structure(staad input) with load...
You are correct. Pdelta effect is computed for primary cases only. So you need to combine different primary loads with appropriate combination factors using REPEAT LOADs instead of using LOAD...
View ArticleCan anyone provide design file of structure(staad input) with load...
code:1893 PART -2 2014 states "while design staging for elevated reservior we need to analyse the structure considering P-delta effect.But in staad help it quotes " p - delta effect is considered for...
View ArticleRAM Concept - Added Tendons
I've just started using RAM Concept and am having issues where I have 'added tendons'. I am continually receiving "WARNING: A generated tendon at (()()) was trimmed which resulted in a % loss of...
View ArticleClik here to view.
RE: RAM Concept - Added Tendons
Check the generated tendons layer to see what was trimmed. It should be visually apparent. If you have more tendons in an end bay, we recommend a second tendon line: For the half-span ratios, make sure...
View ArticleRE: STAAD v8i6 to Tekla 2016 Export
I signed off on the release with Tekla last week. it's just a matter of them posting it to their extranet as far as I know.
View ArticleSTAAD v8i6 to Tekla 2016 Export
HiDoes anyone tried to export a staad file to Tekla 2016?Procedures and set-up are much appreciated.I tried export then import. I am also looking for loads and load combination to be exported to tekla...
View ArticleRE: FORCE FOR COLUMN DESIGN
Please note that the column is a braced long column and it requires a different design procedure. You have to check if the column has a single curvature or a double curvature. As per clause...
View ArticleClik here to view.
FORCE FOR COLUMN DESIGN
Dear All,Kindly go through attached staad model. For design of column member number 229 staad givesPu = 2937.94Mz = 284.05My = 13.5In post processor My value of 13.5 is not appearing.Please help to...
View ArticleClik here to view.
RE: STAAD Foundation Advanced: Machine Foundation Wizard
You may want to follow the following links which has the discussion on this topic.Also, you can visit our Bentley learn server and check for detailed reference on the Designing of machine Foundation
View Article