RE: Staad Post processing results.
The moments that you are getting in the statics check table about the X axis are obtained by doing an algebraic summation of all the MX support moments ( which is zero for load case 3 ) plus the MX...
View ArticleStaad Post processing results.
I have a doubt in the reaction tab in post processing of staad. In Static check results, its shows three rows namely as loads, reactions and difference. In which difference is almost or is equal to...
View ArticleRE: Influence Surface Results are missing or invalid
Using the Geometry selection cursor, I selected the plates and all the beams in X and Z. Went to Deck > Create Deck to include these as part of the deck definition. Defined a straight roadway...
View ArticleRE: Influence Surface Results are missing or invalid
I use Staad 20.07.11.45 to open "Bridge 5_modified.std" and "Bridge 5_modified_deck.std". The "Bridge 5_modified.std" is opened fine, but it has no definition of deck. When I open "Bridge...
View ArticleClik here to view.
RE: Surface forces vs Results along line from Plate Model
Yes, do not cut sections through nodes. For your plate model, I cut a section through the plates at elevation 109 inches which is 1 inch above the nodes at the 9 ft elevation. I compared the Total...
View ArticleSurface forces vs Results along line from Plate Model
[View:/cfs-file/__key/communityserver-discussions-components-files/5932/surface.std:940:0][View:/cfs-file/__key/communityserver-discussions-components-files/5932/5684.plates.std:940:0]
View ArticleRE: Instability at Joints
I noticed you made the supports fixed. I'm planning my designed column to be connected in base plate. My question is the support to be assigned for this is fixed or pinned support? Thank you for your...
View ArticleRE: Influence Surface Results are missing or invalid
You DO NOT need to open the file Bridge 5_modified_deck.std. Just open the file Bridge 5_modified.std, go to the Bridge Deck tab and you should see the roadway colored in blue. Go to Deck > Select...
View ArticleRE: Instability at Joints
The type of support you would use for the base of the column would depend on the connection you have at the base of the column and whether it is able to resist moment or not. If it can, you can use...
View ArticleInstability at Joints
Good day, I would like ask for some advice regarding this structure and its instabilities at joints 6 and 27. How should I go about rectifying this. And will it affect the design?STAAD SPACESTART JOB...
View ArticleRam Elements to Ram Concept
I'm looking for a way to transfer Ram Elements loads to a Ram Concept model. Both have the ability to use ISM repositories, but I haven't figured out how to set a foundation level in Ram Elements in...
View ArticleRE: Indian codes in RAM Connection
Sir, I am using Ram Connection integrated with STAAD.Pro. Most of Structural Engineers I met here are willing and always talk as when it will be available and I am not talking about some small firms...
View ArticleIndian codes in RAM Connection
Dear All,When Indian Codes and sections will be available in RAM Connection?RegardsKaushal Aggarwal
View ArticleRE: Design of pile in STAAD Foundation Advanced per Indian Code
Sir, I am talking about drilled and driven pier foundations same as you have mentioned above. I can see those are available in 1. Machine Foundation Mode only for US codes and 2. Foundation Toolkit...
View ArticleRE: Influence Surface Results are missing or invalid
OK, I can find the roadway colored in blue and the "Deck 1".But when I run "Influence surface generator", I still got the same error "Influence surface resulits are missing or invalid"
View ArticleRE: STAAD: Convert Truss Model to Plane Frame
Hello, If you want to convert truss model to frame model, you can simply delete the "truss specification" as I suspect it was there in General > specs or in the same location you can find "moment...
View ArticleRE: Ram Elements to Ram Concept
Ram Elements does not export support reactions to ISM. A colleague of mine wrote a spreadsheet to make it easier to import load data into a Ram Concept file that you might find interesting, however....
View ArticleRE: STAAD: Convert Truss Model to Plane Frame
Unfortunately, I don't have any specifications listed under General>specs. Back when the project was created, it was set as "Truss" instead of "Plane".How/where can I upload the model?
View Article